RUCKUS Certified Networking Implementer v1.0
Question 1
Which command will transfer a code image between flash modules, from the primary partition to the secondary partition?
- A. copy disk0 flash TNR08095hufi.bin primary
- B. copy disk0 flash TNR08095hufi.bin secondary
- C. copy flash flash secondary
- D. copy flash flash primary
Answer : C
Question 2
When running FastIron SPS08095e code, which step is required to define static routes?
- A. Change the ICX image version to SPR08095e.bin.
- B. Install the L3-prem license.
- C. Run the UFI code image for GZR08095h.
- D. Upgrade to version SPS08095h or later.
Answer : A
Question 3
When using zero-touch stacking, which two prerequisites must be in place to ensure all devices join the stack? (Choose two.)
- A. configure each unit's management IP, VLANs, and tagging
- B. enable stacking on all devices
- C. enable stacking on the active controller
- D. ensure units have clean configurations
- E. issue stack disable on intended member devices
Answer : CD
Question 4
Which two processes are used to add a new stack member to an existing stack? (Choose two.)
- A. stack priority configuration
- B. interactive setup
- C. stack switchover
- D. stack suggested-id
- E. manual configuration
Answer : AE
Question 5
What is the maximum Wattage fur a PoE+ interface with PoE overdrive enabled?
- A. 90
- B. 60
- C. 30
- D. 45
Answer : D
Question 6
Which two Power over Ethernet (PoE) features on the ICX will be enabled by the inline power poe-ha command? (Choose two.)
- A. power priority
- B. Fast Boot
- C. PoE Overdrive
- D. Perpetual PoE
- E. power limit
Answer : BD
Question 7
Which command assigns an interface to an area?
- A. ip ospf area 0
- B. area 0
- C. router ospf
- D. ip ospf cost 100
Answer : A
Question 8
Which command will create VE 2 on an ICX running FastIron 08.0.95?
- A. ICX(config-vlan-2)# router-interface ve 2
- B. ICX(config-vlan-2)# interface ve 2
- C. ICX(config-vlan-2)# enable
- D. ICX(config-vlan-2)# vlan 2 name VE2
Answer : A
Question 9
Review the following configuration.
A RADIUS server is connected and working. However, a switch technician has forgotten the RADIUS username/password for the ICX. When RADIUS is not functioning, they expect to be able to plug into the console port and use the local username/password as a backup.
The ICX does not accept the local password.
Why can't the technician log in?
- A. The AAA web-server configuration is missing the radius keyword.
- B. Local username/password is only used for SSH and web access.
- C. Based on the AAA login command, local password will only be used if the RADIUS server is unavailable.
- D. Based on the AAA login command, local should be in front of radius for correct backup operation.
Answer : C
Question 10
A Core, Aggregation, Edge topology network is running Rapid Spanning Tree Protocol (RSTP). Two switches at the edge are legacy and run 802.1D.
To influence the convergence time of the legacy switches at the edge, where are the timers modified?
- A. the route-only port on the upstream gateway
- B. on the two legacy 802.1D switches at the edge
- C. on the Aggregation switches connected to the legacy edge switches
- D. on the root bridge at the core
Answer : C
Question 11
Which three objects can be assigned a Layer 3 address? (Choose three.)
- A. Stack Interface
- B. VxLAN
- C. Virtual LAN
- D. Virtual Ethernet
- E. Loopback
- F. GRE tunnels
Answer : DEF
Question 12
Based on the following configuration, which statement is true?
ICX-Router (config)# ipv6 unicast-routing
ICX-Router (config)# interface ethernet 1/3/1
ICX-Router (config-if-e1000-1/3/1)# ip address 10.172.10.1/24
ICX-Router (config-if-e1000-1/3/1)# ipv6 address 2001:db8:12d:1300::/64
- A. The ipv6 enable command must also be configured at the interface level.
- B. The interface will transmit and receive both IPv4 and IPv6 traffic simultaneously.
- C. ICX devices do not support IPv4 and IPv6 addresses configured on the same interface.
- D. ICX devices only support dual-stacked IPv4 and IPv6 configuration on a VE interface.
Answer : B
Question 13
Which statement is true about Secure Shell (SSH) functionality in FastIron 08.0.95?
- A. Default login timeout is 30 seconds.
- B. Default SSH authentication type is RSA with 2048-bit modulus.
- C. Server function is disabled by default.
- D. Outbound SSH sessions are not supported.
Answer : B
Question 14
For multicast clients to stop receiving traffic using a leave request, which protocol must run on the local subnet?
- A. IGMPv2
- B. IGMPv1
- C. PIM Dense
- D. IGMP Snooping
Answer : A
Question 15
Which two statements are true when Dynamic Host Configuration Protocol (DHCP) Snooping is enabled? (Choose two.)
- A. DHCP server interfaces should be trusted.
- B. All interfaces are trusted by default.
- C. DHCP snooping must be enabled globally.
- D. DHCP snooping must be enabled per VLAN.
- E. DHCP snooping must be enabled per interface.
Answer : AD