HPE Compute Solutions v1.0
Question 1
Which process does NVIDIA NIM accelerate?
- A. Getting a trained model ready to run in production
- B. Fine-tuning a pretrained model
- C. Deploying data pipelines for AI workloads
- D. Designing an AI project workflow
Answer : A
Question 2
Refer to the exhibit.
Which statement about this logical interconnect group is true?
- A. Both master modules are located in the same HPE Synergy frame.
- B. The master modules are located in the interconnect bays 2 and 5.
- C. For the given downlink speed, the maximum number of frames is reached.
- D. To use interconnect bay set 3, all compute nodes must be half-height.
Answer : C
Question 3
HOTSPOT -
Your customer is implementing an HPE Synergy solution based on three frames.
Click each of the ports that can be used to connect satellite modules.
Answer : 
Question 4
DRAG DROP -
Match each HPE Synergy logical component with the definition.
Answer : 
Question 5
You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support.
Which interconnections are required to support this connection? (Choose two.)
- A. HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy
- B. Brocade 16Gb Fibre Channel SAN Switch Module for HPE Synergy
- C. HPE Virtual Connect SE 16Gb FC Module for HPE Synergy
- D. HPE Virtual Connect SE 32Gb FC Module for HPE Synergy
- E. Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy
- F. HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy
Answer : AF
Question 6
Your customer plans to add four HPE Synergy frames to an existing management ring. All installed frames are equipped with two 2-port FLM modules, while new frames will be equipped with 4-port FLM modules.
Which statement about mixing different FLM modules is true?
- A. Existing 2-port FLM modules must be replaced with 4-port FLM modules.
- B. Mixing different FLM modules is allowed if all of them have the same firmware version.
- C. A management ring with mixed FLM modules cannot have more than 12 frames.
- D. A management ring can contain mixed frame link module configurations.
Answer : D
Question 7
Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames.
How will this change impact the customer environment?
- A. The customer can add a new logical enclosure to the existing setup, because the maximum number of logical enclosures in a single management ring is not reached.
- B. The customer has to expand the management ring capacity either by adding HPE Composer 2 modules or adding memory to reach 128GB per module.
- C. The customer has to create a new management ring for new logical enclosure, because the maximum number of frames in a single management ring is reached.
- D. The customer can add a new logical enclosure to an existing setup once all required licenses are added to HPE OneView and associated with the new frames.
Answer : A
Question 8
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They plan to use Distributed Switches and DRS cluster.
You are preparing a proposal with the following components:
- HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
- two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
- an appropriate number of the vSphere Standard license for each compute node
- one HPE D3940 Storage Modules with 40 SSDs - all required cables and options
Which statement about this proposal is true?
- A. 2 additional HPE Synergy 480 Gen10 Plus compute modules can be added to this setup.
- B. vSphere Standard licenses should be replaced with Enterprise Plus licenses to enable requested features.
- C. 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drives.
- D. One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50Gb/s ILM.
Answer : B
Question 9
Your customer plans to deploy HPE OneView for VMware vCenter Server together with HPE Storage Integration Pack for VMware vCenter. The customer wants to use them to manage HPE Synergy Gen10 compute modules, HPE ProLiant Gen10 servers and an MSA array.
Which statement about compatibility of the existing environment with the planned software components is true?
- A. HPE Storage Integration Pack for VMware vCenter does not support MSA arrays.
- B. HPE OneView for VMware vCenter Server does not support standalone HPE ProLiant servers.
- C. To use the required plugins, HPE ProLiant Gen10 systems must be managed using HPE OneView.
- D. Both HPE Synergy Gen10 full-height compute module plugins will require a license.
Answer : A
Question 10
Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed. They plan to deploy a second nPar and HPE Superdome Flex 280. They play to manage new components using HPE OneView.
What must be done to achieve this goal?
- A. The customer must use iLO5 to add HPE Superdome Flex systems to HPE OneView.
- B. The customer should deploy an HPE OneView appliance for HPE Superdome Flex management.
- C. The customer must add a second Rack Management Controller for HPE Superdome Flex 280.
- D. The customer has to add HPE Superdome Flex to the HPE OneView used to manage HPE Synergy.
Answer : B
Question 11
Your customer plans to deploy a VMware ESXi with HPE Synergy platform. They also plan a vSAN deployment leveraging HPE D3940 Storage Modules and SSD drives.
The customer requested the following components:
- HPE Synergy frame with ten HPE Synergy 480 Gen10 Plus compute modules
- Two HPE Virtual Connect SE 100Gb F32 Modules for Synergy
- An appropriate number of vSAN Standard licenses for each compute node
- One HPE D3940 Storage Module with 40 SSDs – All required cables and options
Which statement about this request is true?
- A. vSphere licenses should be added, as vSAN licenses do not replace vSphere licenses.
- B. vSphere Standard licenses should be replaced with Enterprise Plus licenses to enable vSAN.
- C. 20 SSD drives should be removed from this setup, as D3940 supports only 20 SSD or SAS drives.
- D. One HPE Virtual Connect SE 100Gb F32 Module for Synergy should be replaced with 50Gb/s ILM.
Answer : A
Question 12
A logical interconnect group can span on multiple HPE Synergy frames for which interconnect type?
- A. HPE Synergy 12 Gb SAS Connection Module
- B. Brocade 32GB Fibre Channel Switch Module for HPE Synergy
- C. HPE Virtual Connect SE 100Gb F32 Module for Synergy
- D. HPE Virtual Connect SE 23 Gb FC Module for Synergy
Answer : C
Question 13
Your customer has the following HPE Synergy setup:
- 3 HPE Synergy 12000 Frames
- 4 HPE Virtual Connect SE 100 Gb F32 Modules
- 2 HPE Synergy 50 Gb Interconnect Link Modules
- 36 HPE Synergy 480 Gen10 Plus compute modules
- 2 HPE Composer 2 modules
Which statement about this setup is true?
- A. To manage all frames, the customer must buy two additional HPE Composer 2 modules
- B. The customer must buy 36 HPE OneView Advanced licenses to manage compute modules.
- C. The customer can add one D3940 Storage Module to each of the frames.
- D. To use all compute nodes, the customer must create at least two logical enclosures.
Answer : D
Question 14
Your customer plans to deploy HPE Superdome Flex and configure two nPars, each based on two chassis.
Which components must be included in the proposal to meet the customer’s needs?
- A. At least four HPE Persistent Memory DIMMs per nPar.
- B. One base chassis and three expansion chassis with licenses.
- C. HPE Superdome Flex Grid licenses enabling connectivity between chassis.
- D. Rack Management Controller for nPar management.
Answer : C
Question 15
Your customer has the following HPE Synergy setup:
- Three frames fully populated with HPE Synergy 480 Gen10 Plus modules and 25Gb/s downlink speed formulating a single logical enclosure
- Two HPE Virtual Connect SE 100Gb F32 Module for Synergy
- Four HPE Synergy 50Gb Interconnect Link Module
- Six HPE Synergy Virtual Connect SE 32Gb FC Modules
The customer needs to add a frame.
Which statement about the expansion of this setup is true?
- A. The additional frame must have HPE Virtual Connect FC modules installed.
- B. The customer has to create a new logical enclosure for the additional frame.
- C. The customer can grow the existing logical enclosure up to 5 frames.
- D. The additional frame cannot have 12Gb SAS connection modules installed.
Answer : C